ICH10 Disk I/O error

[mirapuje]

hi im a new builder. my pc spec is asus p5ql-em/q9550/4gb-ram/WD-1TB/gtx1060/alc1200/tp-link751ND / windows 7

i downloaded the Olarila install for high sierra, (because i believe q9550 doesnt have the SSE4.2 required for mojave)

when i boot the Olarila clover, i can see a disk1: I/O error, then fail at erasing the disk to apfs, message is error at last partition etc etc.

i think this is an ICH10 error with appleAHCI.kext v329? however, how do i go about fixing this? as i am unable to access the usb drive in windows after loading Olarila on it?

your help is much appreciated, looking forward to get the hackintosh up and running, i hope theres life in the system yet.

thanks,

mira.p

[MaLd0n]

[ref]mirapuje[/ref], enable patch ALPM IO Error AppleAHCIPort in config.plist from Olarila image

[mirapuje]

hi maldon,

thanks for your help and also for putting all the resources together.

I enabled the patch and installed HS without problem. when I copied your clover775 folder over to my EFI, the option for IO Error patch disappeared, I managed to put it back myself with the I/O binary patches in config.plist.

Then I installed the nvida webdriver, and that was straight forward without issue.

however I have not yet found a solution for the sound to work. my sound-device should be alc1200 (from Asus p5ql-em), and I tried injecting layout-id 1,2,3,5,7,11,12,13 , none of them worked. the only way the computer would boot into HS is if the layout-id is empty, any other number it would end with the error message 'time out with IOHDADEVICE........"

I have also tried fixed option and suggestions from https://hackintosher.com/guides/get-hackintosh-audio-working/ but neither have not worked.

do you have any ideas/suggestions? your help is much appreciated.

many thanks.

mira.p

[MaLd0n]

[ref]mirapuje[/ref], post ur files

--Run_Me

RunMe.app

[mirapuje]

hi maldon,

please see attached file from the runme.app . hope you can help.

many thanks.

Send me Simons-iMac.broadband.zip

[MaLd0n]

[ref]mirapuje[/ref], try

DSDT.aml.zip

stay with lilu and applealc in clover/kexts/other

[mirapuje]

hi maldon,

thanks for the dsdt, I put it in the refi/clover/acpi/patch, and loaded it in clover startup, however it is the same timeout iohdadevice error. I also tried replacing applehda in extension with older (alc1200) one from internet back in 2009-12, then the Mac would boot with both bios.aml/your dsdt.aml, but neither show any sound output device. I tried Toleda patch also, but no luck still. it seems like applehda is the problem. I have put the vanilla HS applehda back in extensions.

from your website, there are dsdt for p5ql-e and p5q-em which are similar to mine, unfortunately I don't know enough to put the the code into test.

I hope by fixing the hackintosh it would keep my hardware alive for a few more years, that would be amazing.

I have attached my latest zip, please let me know if you have further ideas that we can try out to fix the problem.

many thanks.

Send me Simons-iMac.broadband.zip

[MaLd0n]

[ref]mirapuje[/ref], use my DSDT, reboot and extract new SEND_ME

[mirapuje]

you are right, your dsdt did boot up, although no sound output device still.

please see attached new send_me.zip, thanks.

Send me Simons-iMac.broadband.zip

[MaLd0n]

[ref]mirapuje[/ref], CLOVER.zip

new send_me after reboot

[mirapuje]

new send_me.zip

thanks.

Send me Simons-iMac.broadband.zip

[MaLd0n]

[ref]mirapuje[/ref], alc1200 = alc888

i think u have a applehda mod, u need a vanila file and inject via clover, devices tab

[mirapuje]

hi maldon,

I copied the vanilla applehda from your Olarila HighSierra USB into S/L/E. then I tried to inject layout-id with 1/2/3/4/5/6/7/11, still no sound output on anyone of them. I have attached my applehda in zip.

is there any other info/data that might help?

many thanks.

Added in 17 minutes 19 seconds:

also please see my clover audio screenshot, it has 2 controller, is that correct?

Added in 2 minutes 58 seconds:

and this is the error message from my bios.aml + id layout 1

Added in 13 minutes 12 seconds:

correction: i think i have been using your dsdt + inject layout 1 to 11, not bios.aml.

AppleHDA.kext.zip

[mirapuje]

i have also attached my linux codec dump, and my HDEF@1B which i think you would have saw from the zip.

i followed the reddit vanilla applehda guide, still no luck i have been trying mostly layout 1 & 7.

codec_dump0.txt

[MaLd0n]

[ref]mirapuje[/ref], try applehdapatcher

[mirapuje]

hi mald0n,

thanks for the help. i managed to get sound working by installing voodooHDA. kind regards.

[R-88]

On 2/21/2019 at 7:23 PM, MaLd0n said:

[ref]mirapuje[/ref], enable patch ALPM IO Error AppleAHCIPort in config.plist from Olarila image

this patch can't be working on OpenCore. You are sure is working?

[MaLd0n]

25 minutes ago, R-88 said:

this patch can't be working on OpenCore. You are sure is working?

all patch is working in both

[R-88]

ok i will try. Any way to use iMacPro 1,1 on Catalina (legacy bios) wihout MCE kext panic?

Edited May 15, 2020 by R-88

[MaLd0n]

10 minutes ago, R-88 said:

wihout MCE kext panic?

AppleMCEReporterDisabler.kext.zip

[R-88]

21 minutes ago, MaLd0n said:

AppleMCEReporterDisabler.kext.zip 2.93 kB · 1 download

thanx! work! my last question: where i can put -raddvi on opencore? I can't find boot args or similar in config.plist

[MaLd0n]

4 minutes ago, R-88 said:

thanx! work! my last question: where i can put -raddvi on opencore? I can't find boot args or similar in config.plist

nvram

[R-88]

On 5/15/2020 at 9:30 PM, MaLd0n said:

nvram

Two questions:

 

1. there is a patch for ICH10 + Opencore 0.6.7 + Big Sur?

2. there is a way to rename default boot entries on Opencore 0.6.7?

 

Thanx in advance

[MaLd0n]

try it

Quote

<dict>
                <key>#MatchOS</key>
                <string></string>
                <key>Comment</key>
                <string>ALPM IO Error AppleAHCIPort</string>
                <key>Disabled</key>
                <false/>
                <key>Find</key>
                <data>
                QGACAA==
                </data>
                <key>Name</key>
                <string>AppleAHCIPort</string>
                <key>Replace</key>
                <data>
                AAAAAA==
                </data>
            </dict>