macOS 26 Tahoe Hackintosh

[jm26200]

very sorry bad new

So I'm reporting back to you after copying the EFI folder on my SSD. restart
1 - Reset NVRAM
2 - Automatic reboot on the drive

and a screen of lines unreadable given the speed and an additional half screen, and restarting the PC.

I wish you a good afternoon and thank you very much for your dedication and your help.

regard

[MaLd0n]

Post one video 

[jm26200]

on the second screen here is the reboot which arrives after these last lines if that can give you a clue

I will make a video after clicking on install macOS Beta I am not very well equipped with an iPhone X or an iPad mini from 2012 but i try and i see if good

IMG_10233.zip

IMG_6556.zip

Edited June 15, 2025 by jm26200

[MaLd0n]

Your USB kext is not remmaped. U need to use USB2 port.

[jm26200]

hi sir

My USB drive is properly connected to the USB2 port. I'll repeat the process to get the mapped file by following your instructions D, Q, P, A, K.

And I'll check on the Insanelymac forum. I just read a not-so-encouraging post.

maly70
Members
257
Gender: Male
Posted 3 hours ago
Hi, none of my z790, z590, and z490 work with Tahoe. I couldn't install, and at the second boot, I keep getting KernelManager not active.

I did install the latest OC and kext files, removed all USB-related kexts and .aml files. I got SSDT-UIAC, but still, no luck.

 

Good rest    good night  sIR

3:09 go take my breakfeast and go out for walkin 3 km   seee later   for  macos tahoe

great thnxxs 

Regards

 

[Antonio BQ]

Tengo el mismo problema. No tengo teclado ni ratón.

Edited June 16, 2025 by Antonio Belso Quesada

[Slice]

3 hours ago, Antonio Belso Quesada said:

Tengo el mismo problema. No tengo teclado ni ratón.

Because of well known USB issue. See the discussion.

[jm26200]

Hi Daniel. good new morning try again and surprise all. success for install macOS Tahoe

Great thnxsss sir 

tc always

 

regard

PS : but no wiffi later try with itlmw and hairport ????  and  for install  for  arg  only -V

Capture d’écran 2025-06-17 à 07.03.54.zip

Edited June 17, 2025 by jm26200

[Fares Shady]

I have a problem I don't see my NVME SSD inside the installation, I tried to add that NVMeFix.kext and also in the config.plist but it didn't help.
I was so excited to try but now I can't find any solution 😕
I'm so sure my SSD is compatible it's WD I used it before to install Monterey and it worked fine.
Please help me 😞 

[MaLd0n]

Check NVME options on bios/uefi setup.

[Fares Shady]

There is no NVME options in bios, only found sata mode and I changed it to ahci.
Still not working.
I'm using acer predator helios 300 PH315-53 bios so limited.
But how it used to work before?

[MaLd0n]

Nothing about Storage?

[Fares Shady]

Yes nothing only sata mode and if I want to enable ports or not and for me all ports are on

[joaopaulomartins]

Hello MaLd0n

again in a new battle, now to install Mac Os Tahoe in my hackintosh.

I make a pen bootable, but stop in the image attached. Can you help me?

Best regards from Portugal

IMG20250617193503.jpg.zip

[MaLd0n]

Use only mandatory kexts

[Fares Shady]

What about me please :((

[Slice]

23 hours ago, Fares Shady said:

There is no NVME options in bios, only found sata mode and I changed it to ahci.
Still not working.
I'm using acer predator helios 300 PH315-53 bios so limited.
But how it used to work before?

Sorry but the problem with your BIOS.
I have GA170 motherboard with M2 slot. I inserted here NVMe noname drive (China) just boot and install here Clover and Sequoia. Nothing to do in BIOS. Nothing to do in Clover.

Now I boot from EFI from the NVME drive, choose Sequoia and all is fine.

[MaLd0n]

@Slice Can you fix the XHCI patch limit in Clover for Tahoe? 

[Slice]

14 minutes ago, MaLd0n said:

@Slice Can you fix the XHCI patch limit in Clover for Tahoe? 

I will look but I think (as well as Vit9696) that this patch should be avoided because using more then 15 ports per hub may cause undefined behaviour of the system because for port number there are only 4 bits (0..15) and extra bit may overlaps other bit.

The patch may be used initial for testing which connector is from which port to create own port maps. This port maps will exclude some unnecessary ports to have only 15 of them. See my LegacyUSB3.kext
https://cloud.mail.ru/public/KCGk/cRHbqg4sw 

[MaLd0n]

48 minutes ago, Slice said:

I will look but I think (as well as Vit9696) that this patch should be avoided because using more then 15

Yes, Slice. I just need it to create installer for many chipset in one EFI folder only, but after installation we need this remap, is ever the best idea. Thank you!

[Slice]

You may exclude for installation any 4-8 first HS** ports to have SS** ports working. Only for installation!

And then remap.

[MaLd0n]

Yes, but the big truth is that this patch has never caused any problems and continues to work beautifully on the Sequoia. 😁

[Fares Shady]

7 hours ago, Slice said:

Sorry but the problem with your BIOS.
I have GA170 motherboard with M2 slot. I inserted here NVMe noname drive (China) just boot and install here Clover and Sequoia. Nothing to do in BIOS. Nothing to do in Clover.

Now I boot from EFI from the NVME drive, choose Sequoia and all is fine.

But how I used to have macOS before and everything was fine!!

[Slice]

9 hours ago, Fares Shady said:

But how I used to have macOS before and everything was fine!!

It was NVME? And BIOS saw it before? What is changed? Before you started any OS.

[joaopaulomartins]

On 6/18/2025 at 2:33 AM, MaLd0n said:

Use only mandatory kexts

This is for me? What mandatory kexts (virtualsmc /Applealc/Lilu) some more?

Can you send me a EFI paste for my hardware to install Tahoe?

I try with other EFI you put in my sequoia when you make me a virtual assistance.

Thank you