Hackintosh USB Port Mapping Guide 2023

[MaLd0n]

10 minutes ago, mengshi said:

https://1drv.ms/u/s!AumDSEaF6xVbmV26tLmndLZ3dSAo?e=djku4A

DSDT.aml.zip

uncheck xhci port patch, reboot and start remap

remove all ssdts use only dsdt

enable rebase regions

[mengshi]

Sorry, this one didn't work correctly.

 

I managed to get perfection by doing the following:

Researched further and found that for the 9 series of chipset, I needed FakePCIID_XHCIMux.kext and FakePCIID.kext.

 

My process to get perfection (on the Gigabyte H97-HD3 which has 4 physical USB 3.0 and 2 physical USB 2.0 at the rear, 2 USB 3.0 and 2 USB 2.0 at the front (from an onboard header)), Haswell CPU running as Mac Pro 7,1

 

1. Rename EHC1 to EH01; rename EHC2 to EH02, rename XHCI to XHC; rename XHC1 to XHC.

2. Initially untick XhciPortLimit

3. Remove USBInjectAll.kext

.

4. Reboot

.

5. Run corpnewt's USBMap script. This time all 6 SS ports show up numbered nicely 1-6, with USB 2.0 detected on EHC. Plug in a USB 3.0 to each port to register.

6. This time USBMap is correct. Just generate the kext and no need editing.

7. Pot the above USBMap.kext in the correct OC folder, re-tick XhciPortLimit and reboot.

 

--------------------------

If I get you to generate a DSDT with the above current working setting, will it make sense? (Just to try to go the DSDT method).

 

Below is the RunMe link generated with the above perfect setup. Thanks

 

https://1drv.ms/u/s!AumDSEaF6xVbmV6gDLkKa7Rs5Q6I?e=Nonh3P

 

[MaLd0n]

9 hours ago, mengshi said:

I needed FakePCIID_XHCIMux.kext and FakePCIID.kext.

no

u don't need need this shit

this kext set to usb 2 and not usb 3 device

is wrong

[mengshi]

2 hours ago, MaLd0n said:

no

u don't need need this shit

this kext set to usb 2 and not usb 3 device

is wrong

 

No. It works. As Rehabman described it "The effect is to route any USB2 devices attached to the USB2 pins on the XHC ports to EHC1. In other words, handle USB2 devices with the USB2 drivers instead of the USB3 drivers (AppleUSBEHCI vs. AppleUSBXHCI)."

Tested it already. See the screenshot. It is the only way I found that got the 6 USB 3.0 ports under XHC with this series 9 motherboard. Any other methods it displays like the screenshot I showed in previous message.

All 6 USB 3.0 work at correct speed. The USB 2.0 ports are under EHC and the only "problem" is that the devices are not shown in Hackintool but are shown in System Report.

This method is unnecessary with motherboards newer than series 9 (I think.)

 

Screenshot 2021-05-30 at 11.41.20 PM.png.zip Screenshot 2021-05-30 at 11.44.14 PM.png.zip

Edited May 30, 2021 by mengshi

[MaLd0n]

is wrong bro

is a non-sense way

not a good and vanilla solution

with my dsdt u see only xhci device

serie 8+ we just need xhci

[MaLd0n]

*UPDATE FIRST POST*

[XLR]

When i insert usb2 stick, it appears on the desktop in all ports, but many times it doesn't appears in hackintool, is it normal?

[MaLd0n]

5 minutes ago, XLR said:

When i insert usb2 stick, it appears on the desktop in all ports, but many times it doesn't appears in hackintool, is it normal?

some mobos have internal hub

4 ports work inside this hub in screenshot above for example

is common and good for us. we can use more ports in this case

[redx30]

Hi i remap my usb ports and make all the step of this tutorial but mi usb 3.0 dont work with my mouse or keyboard or usb bluetooh  only work with memory usb  so i need remove the usbinjected.kext to work normally  and i have a PCi-e  USB card to extra port but i can use the sytem recognizes but dont work anythinyn port  i dont find any solve to use my extra port on my PCI-e card usb  

the pci-e card is uPD720200 nec corporation

[MaLd0n]

8 hours ago, redx30 said:

Hi

start again

all ports need work if ur remap is correct

[redx30]

5 hours ago, MaLd0n said:

start again

all ports need work if ur remap is correct

hi, i make this tutorial  5 times and  my USB only work with memory usb devices not with peripherals like mouse microphone or keyboard when i use the USBijectec.kext  that kext never work in my hackintosh  but the most importan, is need  working my PCI-E card USB  any solves to make work that ?

[MaLd0n]

2 hours ago, redx30 said:

is need  working my PCI-E card USB  any solves to make work that ?

this tutorial is fot built ins usb ports not pci cards

pci cards need a native support

[redx30]

4 hours ago, MaLd0n said:

this tutorial is fot built ins usb ports not pci cards

pci cards need a native support

who pci-e card you recommend ?

[MaLd0n]

14 hours ago, redx30 said:

who pci-e card you recommend ?

have many

check ebay or amazon

[andytang]

Hi everyone,

I have remap my all my usb port. Final, I have 14 highlight green port on hackintool.

the only problem is that I have usb 3.1 type A and usb 3.1 type C on my Asus Z170-AR.

when I plug my usb 3.1 in both port type A and C, my system detected device and I can use it on both 3.1 usb ports. But on hackintool doesn’t detect device.

I want to know how can I re map the usb 3.1 type A and type C on hackintool.

Thank you very much

[MaLd0n]

On 8/13/2021 at 5:32 AM, andytang said:

when I plug my usb 3.1 in both port type A and C, my system detected device and I can use it on both 3.1 usb ports. But on hackintool doesn’t detect device.

some mobos use internel hub and hackintool dont detect it  detect only HUB

[andytang]

3 hours ago, MaLd0n said:

some mobos use internel hub and hackintool dont detect it  detect only HUB

Thanks for your reply MaLd0n,

So how can I do with this please. Or just leave it what it is and export just 14 ports that already remap on hackintool.

My board is asus z170-AR, I think you did have a look on this already. Do I need to do any more patch dsdt or ssdt patch for it to make complete system.

Thank you very much 

[MaLd0n]

7 hours ago, andytang said:

So how can I do with this please. Or just leave it what it is and export just 14 ports that already remap on hackintool.

hub is a good thing

i have 2 hubs in my mobo, 8 ports into only 2 physical ports

[andytang]

29 minutes ago, MaLd0n said:

hub is a good thing

i have 2 hubs in my mobo, 8 ports into only 2 physical ports

Hi MaLd0n,

I want to mark it as USB C + sw on hackintool. How can I know which port please?

 Thank you very much 

[MaLd0n]

post one screenshot here

[andytang]

14 minutes ago, MaLd0n said:

post one screenshot here

https://imgur.com/a/83a0Lzn

Hope you can help me out. Thank you

[MaLd0n]

6 hours ago, andytang said:

Hope you can help me out. Thank you

is asmedia

in this case is not inside xhci device

u don't need remap it

[andytang]

12 hours ago, MaLd0n said:

is asmedia

in this case is not inside xhci device

u don't need remap it

Thank you very much. I will leave it as is and just remap only 14 port show up on hackintool. Thank you

[Alejandro Barreiro]

MaLd0n Excellent tutorial !!!
Thanks.

[MaLd0n]

Enjoy!