Install MacOS with Vanilla Olarila Image, Step by Step

[tominhthanh2308]

When boot complete, my disk unity can't detect my HDD. In BIOS, sata config is AHCI, please help me. Sorry my english is bad

[underdrive]

Thanks!Send me nichs-iMac.zip

[MaLd0n]

[ref]tominhthanh2308[/ref], use boot key for load usb stick with apfs/hfs drivers

Added in 46 seconds:

[ref]underdrive[/ref], i edited ur files, is same files, don't need edit again, just update clover and kexts

[NOTORIOUS VR]

So I did a fresh install of Catalina with your image... at first I couldn't install because no SMBIOS was set at all (empty/blank) - Set to iMac 13,2 and I was able to continue the installation.

After this I followed the instructions on the first page, Clover 2.5 r5096 warns that it is not compatible with this OS version, and then fails to install at all.

I don't know what to do now. I haven't deviated at all from your instructions except change/edit config.plist fir SMBIOS setting.

Any ideas?

[MaLd0n]

[ref]NOTORIOUS VR[/ref],

run it

https://Olarila.com/files/Utils/disablehibernate.command.zip

and it

https://Olarila.com/files/Utils/master-disable.command.zip

and try install clover again

if u use a uefi mode don't need install clover, just put efi folder inside efi partition

[NOTORIOUS VR]

Hi, thanks for your quick reply but I believe the issue was a mistake of my own when I formatted/partitioned the drive on the previous installation. I reinstalled (and erased the disk again) and now Clover installation is ok. Also I did run the scripts just as you advised in your main post.

I am following the steps now to install the EFI folder and the files you made for me. I will report back soon.

Thank you again.

EDIT: Spoke too soon.

I was able to install Clover the first time, then I copied your EFI folder and now I cannot install it again over it as you suggest - it fails at the same point as before. I will copy the files manually as I am booting UEFI only.

[luizteck]

Problemas ao tentar instalar no Sony VPC-EH30EB está dando o erro "ehci controller unable to take control from bios"

Alguém já conseguiu instalar num desses? Gostaria de um auxilio para poder instalar nesta máquina. Estou tentando o El Capitan.

[MaLd0n]

[ref]luizteck[/ref], veja se funciona

EFI.zip

[noiiz]

Na instalação do Catalina em um Dell Inspirion altero o config para config2 e começo a instalação só que só aparece uma pequena barra cinza e fica nisso por uns 10-15 minutos até o note reiniciar, não mostra nenhuma mensagem nem nada, tem algo que possa fazer para mostrar logs ou algo do tipo ?

[MaLd0n]

[ref]noiiz[/ref], não precisa do config2, use o default

[bobenia]

installation finished succesfully on my ASUS Notebook.

After restarting it loads until Welcome Screen them it restarts.

Notebook specifiactions https://www.asus.com/me-en/Laptops/K556UR/specifications/

any ideas how to fix this?

[noiiz]

noiiz, não precisa do config2, use o default

 

Mesmo com o config default fica da mesma forma, apenas uma "barrinha" cinza e depois de 15 minutos +o- a tela a barrinha some e o note reinicia:

Já usei o Olarila Catalina.raw e o Olarila Catalina Intel.AMD.raw , com o mesmo resultado nos 2

[noiiz]

Tentei o Mojave tambem, e fica na mensagem Start Initdevicetree e não tem mais nenhuma ação após

[MaLd0n]

[ref]noiiz[/ref], primeiramente atualiza a sua assinatura pra gente saber qual é o hardware

[noiiz]

Atualizei com os dados que possuo;

é um Note Dell Inspiron 7559 i7 6770HQ , NVIDIA 960M, 16gb ddr3, SSD Corsair 512Gb

[MaLd0n]

[ref]noiiz[/ref], tenta com -x pra desativar alguns drivers, safe mode

[noiiz]

Tentei com o -x (barra de espaco no menu e marquei o checkbox) tanto no Mojave quanto no Catalina, os 2 ficam da mesma forma (Mojave para no Start Initdevicetree e o Catalina na barrinha cinza e depois reinicia )

Criei o pendrive no windows com o Win32DiskImager tem algum problema ?

[MaLd0n]

[ref]noiiz[/ref], eu usei esse programa há muito tempo atrás, não sei como está hj em dia, mas deve funcionar, só extrair a imagem antes de queimar

[nithinxjohnson]

@MaLd0n

I am having a nvidia gtx 1050 on my high sierra . I can't find a good guide to get full acceleration for my gpu

..can you plz help me..

Thankz in advance...

[MaLd0n]

[ref]nithinxjohnson[/ref], use it

https://Olarila.com/files/Utils/nvidia-update.command.zip

check NvidiaWeb in System Parameters tab

and clear nvram with F11 in Clover boot screen