[Guide] Hardware Encoder / Hardware Decoder / Video Processing / HEVC Support / Intel Quick Sync

[gugadj]

Ola Mald0n como vai, nao consegui ativar aceleracao segui o tutorial troquei o clover e nada minha configuracao coffeelake i78700k mobo z370 gaming5

[MaLd0n]

[ref]gugadj[/ref], é só seguir o tutorial e ativar a IntelHD no bios/uefi, não tem erro

[gugadj]

é só seguir o tutorial e ativar a IntelHD no bios/uefi, não tem erro

ok Mald0n mas eu terei que usar a intelHD ou poderei continuar usando a GTX 680 pelo visto so vai dar aceleracao para a intel

[MaLd0n]

[ref]gugadj[/ref], a intel fica "dormindo" e só vai ser usada pra vídeo, h264, etc, a sua gpu principal continua sendo a nvidia, segue normal

[gugadj]

a intel fica "dormindo" e só vai ser usada pra vídeo, h264, etc, a sua gpu principal continua sendo a nvidia, segue normal

ok Mald0n thanks work! so nao deu QE CI na GTX

[MaLd0n]

[ref]gugadj[/ref], esse procedimento é somente pra hardware accel, nada tem a ver com driver de vídeo off board

[makmp]

Hello to the whole team, I've installed Mojave 10.14.4 but there is no hardware acceleration although my card is shown in devices and graphics but is not recognised from videoproc hardware info. My three monitors work properly without problem. I haven't install any kext. My machine is just after replacing clover folder for my chipset X299. There is no on-board graphics on my Mobo.

Mobo: Asus rog strix X299 gaming-e

Processor: i7 7820x

Graphics Card: Radeon RX 580

[MaLd0n]

[ref]makmp[/ref], intel quick sync dont work in ur case, u can try fake ur gpu with a amd pro

AMDRadeonPro.kext.zip

[makmp]

I did that, my card is recognized in videoproc but no acceleration. Sending you 2 photos in the zip.

Desktop.7z

Edited April 6, 2019 by Guest

[MaLd0n]

[ref]makmp[/ref], i think video proc use intel quick sync, i never test it with other gpu

[makmp]

makmp, i think video proc use intel quick sync, i never test it with other gpu

 

Thank you very much for the help!!!

[Najr4d]

Hello to the whole team, I've installed Mojave 10.14.4 (18E2034) for Asus Prime Z390-A + i9 9900K+ SMBIOS: iMac 19.1+ MSI RX580 Armor 8GB. Should it be like that? my iGPU can not be seen in the system report. VideoProc says that h264 and HEVC are good. FCPX does not use iGPU. IntelPoweGadget shows when I use VideoProc that iGPU works. Only RX580 works on FCPX. How to make FCPX work with iGPU? - This is what I care about most Sorry for my bad English

CLOVER.zip

[MaLd0n]

[ref]Najr4d[/ref], IGPU system use only if need, 4k h264 for example

[Najr4d]

MaLd0n I know, I have an i7 4790K on which I work perfectly. When FCPX exports iGPU sometimes works, sometimes not. At i9900K, all the time rests during export to h264, and RX580 is loaded at 100%. Could you look at my EFI? Config.plist made by friends from Hackintosh.de - supposedly specially under Asus PrimeZ390A. There are things that I do not understand. And graphics fixes other than yours. On this config.plist 10.14.4 there are no problems, audio works, sleep / wake shutdown and UHD630. But in FCPX it's worse. I will still test

[MaLd0n]

[ref]Najr4d[/ref], post full dump

--Run_Me

RunMe.app

">

[erroruser]

[ref]Najr4d[/ref], use clover config from here https://Olarila.com/files/Clover.Folder/CLOVER.SERIES.100.200.300.zip then

make sure your bios is current an add in values from here to your config plist with clover config

-Coffeelake(9 Gen)

IntelGFX 0x3E928086

ig-platform-id 0x3E910003

Check InjectIntel

shikigva=60

set smbios for imac 19,1

for bios gpu see here https://drive.google.com/open?id=1eP5kTh4IlBgKpbbr7DHndIeaRqIIS417

once Maldon has done dsdt place in the efi/efi/clover/acpi/patched folder

[Najr4d]

As soon as I come back home, I will do these things and write.

Thank you for your interest in my case.

[Najr4d]

Ok. I did this on the EFI which I gave in the post from 20 Apr 2019, 23:35

Send me Najrads-iMac.zip

[MaLd0n]

[ref]Najr4d[/ref],

1- Replace Full Clover Folder

CLOVER.zip

2- Install Clover again with correct options

Last Clover Version UEFI

3- Reboot

4- Extract new Send_me

[Najr4d]

Yes Sir! Done:

Send me Najrads-iMac.zip