Stuck in installation start +++++ signs

[crisorlandobrsp]

I was able to install Mojave and Catalina with no problem here, did not install any EFI to the NVME since I was trying to check if it was some mistake at my BIOS settings

I was not using Hackintosh for a while since I was using Nvidia 1060 and now I got a 5600XT 

 

I know my CPU is from older gen (1155 i7-3770K) but it has a good and stable overlock fixed at 4.7 and using a PCIE nvme (Corsair 510 2tb) that works fine with Mojave and Catalina (10 min install)

 

Motherboard ASUS Sabertooth Z77 with 4 x 8GB Gskill TridentX 2666Mhz 

 

It has a few addon cards (4 ports realktek LAN (using only the 1st port now, and Mojave and Olarila works fine) Firewire, ASMEDIA sata controller) and a USB 3.0 PCIE too 

 

it says something about wake failure and some kernel stuff I really don't understand

 

Got the image from mediafire (the updated one)

Tks

20201208_100931men.zip

[crisorlandobrsp]

I was able to install OpenCore EFI from a facebook post (Olarila group) but it stucks in the middle and fails

 

Any way to actually install ?

[MaLd0n]

-OpenCore Vanilla Guide
https://www.olarila.com/topic/8918-opencore-vanilla-guide-step-by-step-full-dsdt-patched-or-ssdt/

-Clover Vanilla Guide
https://www.olarila.com/topic/5794-hackintosh-guide-install-macos-with-vanilla-olarila-image-step-by-step-install-and-post-install-windows-linux-or-mac/

[crisorlandobrsp]

On 12/10/2020 at 12:33 AM, MaLd0n said:

-OpenCore Vanilla Guide
https://www.olarila.com/topic/8918-opencore-vanilla-guide-step-by-step-full-dsdt-patched-or-ssdt/

-Clover Vanilla Guide
https://www.olarila.com/topic/5794-hackintosh-guide-install-macos-with-vanilla-olarila-image-step-by-step-install-and-post-install-windows-linux-or-mac/

Hi

Clover still stucks in the ++++++ signs and Opencore was having ACPI states hanging in the installer (acpi sleep states s3 s4 s5)
I used nullpowermanagement kext inside opencore kext folder and now it booted to the installer and when it was 13 min to finish it had a kernel panic regarding iographics 

Gonna try not using my ACPI settings and if still fails gonna install Catalina only to be able do dump and reassemble ACPI tables 

Tks

[lukakeiton]

9 hours ago, crisorlandobrsp said:

Hi

Clover still stucks in the ++++++ signs and Opencore was having ACPI states hanging in the installer (acpi sleep states s3 s4 s5)
I used nullpowermanagement kext inside opencore kext folder and now it booted to the installer and when it was 13 min to finish it had a kernel panic regarding iographics 

Gonna try not using my ACPI settings and if still fails gonna install Catalina only to be able do dump and reassemble ACPI tables 

Tks

Remove this kext. Use Kernel->Emulate->DummyPowerManagement.

Use agdpmod=pikera boot-flag for your graphics. NVRAM -> 7C436110-AB2A-4BBB-A880-FE41995C9F82 ->boot-args

[crisorlandobrsp]

On 12/12/2020 at 7:11 AM, lukakeiton said:

Remove this kext. Use Kernel->Emulate->DummyPowerManagement.

Use agdpmod=pikera boot-flag for your graphics. NVRAM -> 7C436110-AB2A-4BBB-A880-FE41995C9F82 ->boot-args

Hi

I was able to install with no problems before seeing the reply 
Everything works fines but overclock and the new GPU (Navi) does not show temps

Tks