dacicus

Ok, merci beaucoup !

Thank you for fast reply, even with Z590 ? I'm about to buy the same GA Z590 UC AD with a 10400f and I wanted to be sure for Mojave before.

Hi Daniel, I've spent some time looking to see if it's possible to install Mojave on Z490, Z590 and 10 gen CPU, but I haven't found anything reliable. Some people say it's possible by using a fake CPU. Can you please confirm or deny if you know more? Thanks

Thank you MaLd0n for continuing to try to help me. The good news, with your DSDT and the SSDT-UIAC I made under Clover, I finally managed to boot with OC 0.6.5. I didn't dare before to put the DSDT.aml in Opencore's ACPI folder, because it's not recommended in the Dortania guide I started with - why does it do that anyway? I started with just CSM, CFG-Lock and Serial Port disabled and here I am, I still have this "disk not ejected properly mac" message with another usb key plugged in. The first one by the way gave up the soul, I don't know why?!

Finally, I'm sorry about, I think I spoke too fast the second time! The flash drive continued to disconnect at the beginning for a few minutes, but not since then. I hope it will last... Anyway here are the options of the Bios: Disable Fast Boot Secure Boot Serial/COM Port Parallel Port VT-d (didn’t find) CSM Intel Platform Trust (didn’t find) CFG Lock (MSR 0xE2 Enable VT-x (didn’t find) Above 4G decoding Hyper-Threading Execute Disable Bit EHCI/XHCI Hand-off OS type: Windows 8.1/10 UEFI Mode (didn’t find) SATA Mode: AHCI

I spoke too fast, even if USB3 now works the continent USB flash drives to disconnect themselves ... The nightmare continues

HI Maldon, just to say you is ok now for Clover boot. Using your DSDT I finnaly managed to make a good SSDT with USBInstallAll and Ioregistry. Keep trying with OC. Thank you very much

Back to the Opencore again Now I stack on this : applebuspowercontroller request static service power locked : power supply unavailable, assuming succefull power for HS09 etc HS10 etc... Again relative to USB

Thank you, so, what can be then ? What else I can try ?

It is normal that "About this mac" show only a USB 3 controller now ?

Did it, but unfortunately no joy. Tried mapping with Hackintool and Usb.map but no, USB 3 not working "Disk not ejected properly" for a usb flash after some seconds

Thank you men, I've booted with the config file you send me first and the DSDT.aml. I have just XHC now for usb but it's still not working! Here is the new dump https://kmu.files.cnow.at/s/4iYyqJEb2issnZm

Here is the link : https://www.dropbox.com/s/btzoc940e8ncvxd/Send me CTs-iMac.zip?dl=0

Nightmare, got back to Clover for the moment because I can't even boot with Opencore. I finally managed to do usb mapping with USB.MAP by booting with USBInjectAll.kext and XHCI-unsupported.kext but by rebooting with USBMap.kext the Usb3 ports don't work, a usb flash ejects itself, it's very strange, sometimes the usb flash drive appears, sometimes not... What to do ?

No, same thing Screen_OC1.zip

Thank you MaLdon I took your advice (I made a small donation by the way) and tried Opencore for the second time. I had tried it before and couldn't get it to boot, and that's why I went with Clover. Just like the first time I got the same result: Stuck at IOConsoleUsers: gIOScreenLockState 3

Impossible to boot with the config you send me

Same result I send you with my config in case https://www.dropbox.com/s/7k79bsmx31e84j6/Send me CTs-iMac.zip?dl=0

Thank you But I can't boot with your config, here is a picture 20210103_132935.zip

Hi, I'm running High Sierra on a Jingsha x99 d8 motherboard, e5-2678 v3, GTX 1060, everything is fine except USB 3 I tried just about everything I found, but nothing appears in IORegistryExplorer when I insert a USB flash drive. I'm in High Sierra, I applied the limit patch, and put USBInjectAll.kext. Thanks x99 D8.zip