foliasis

I did that but still the same

but it doesn't mount it shows without any change in kexts also If I use AnyCardReader.kext it is identified as Apple Internal Card but does not mount on inserting the sd card Added in 7 minutes 51 seconds: Another thing that i have observed is that of I plug in a pen drive in the USB2.0 port it loads as USB 2.0 CRW in the ioreg. May be the card reader is not able to load the correct drivers but I don't know how to do it

It still stays the same ioreg attached MacBook Air.zip

Here is the zipSend me MacBook-Air.zip

Sorry. I'll get back with the zip.

Hi me again. So I have got almost everything working on my Dell Vostro 3558 with Mojave 10.14.1 Lastly what remains is the SD Card. (Realtek USB 2.0 CRW). It is shown in System Report but the card is not mounted. What I tried- 1. AnySDCard.kext (changing the id everything) 2. CustomPeripheralDevice.kext 3. AppleStorageDrivers.kext (edited the ids as stated in the thread) None of them seem to work. Any help will be appreciated

Thanks everyone for you help. What worked for me. 1. Realtek ALC 255 - AppleALC/Lilu in L/E and injecting layouts-id=7 and alc-layout-id=3 under Device/Properties 2. Synaptics Trackpad - ApplePS2SmartTouchpad.kext in L/E (Voodoo works partially) and Roollback Touchpad Prefpane from Sierra to get the double tap etc working.

I'll see about the trackpad. Will try what you suggested. What to do about Realtek ALC 255?

I copied the Clover folder that you attached, rebuilt the cache and rebooted. When running the Runme.app the application hangs on retrying to get the ioreg dump. However in the first post I have attached all the necessary files in a zip that I extracted manually. Can you have a look at those? Or help me extract using Runme.app?

Ok thanks. I will try in an hour (presently at my clinic). Can you give some ideas how to get my audio working (Realtek ALC255) tried AppleALC+Lilu but no audio output devices. Also the next output gives some error I have uploaded that in the zip file as text. Thanks again

It is from Mojave. I had used some I2C patch as well but it doesn't work. Can you help me with the audio?

Thanks a lot @onemanosx for the prompt reply. 1. I was able to get the I2C Trackpad working with High Sierra using the VoodooI2C kexts, DSDT patch that were mentioned in the post. But since Mojave (10.14.1) I am unable to do that. When I use VoodooPS2Controller.kext I can use the touchpad but no tap to click or multi finger gestures. So can you help me get Tap to click work with Mojave? 2. I have rebuilt the DSDT from scratch after Mojave upgrade. 3. My Realtek ALC 255 is also not working with AppleHDAPatcher(Mirone audio 10.9)/AppleALC+Lilu+Inject id 2 (under Device/Properties in config.plist-Clover). 4. All of these were working in high Sierra 5. I have uploaded ioreg.zip in the first post it includes Clover/DSDT/Terminal Kext Output/ioreg Thanks again for sparing your time.

Hi this is my first post on this forum. Please correct me if I make mistakes or break forum rules. I have successfully installed Mojave 10.4 on my Dell Vostro 3558 (Intel Corei3-4005U/Realtek ALC255/I2C-HID Touchpad Synaptics-Dell). Previously I was able to use I2C Trackpad and audio in High Sierra using VoodooI2C with DSDT Patch and ApplePS2SmartTouchpad.kext and the audio by using HDAPatcher(MironeAudio) and using the patched kexts and config.plist and DSDT patch. However in Mojave I am unable to get audio using HDA Patcher or Apple ALC using layout 2 Also its not relevant to this post but I am unable to get I2C Touchpad working. I tried VoodooI2C and related files, AppleSmartTouchpad.kext. The touchpad works using VoodooPS2controller.kext but there is no tap to click or gestures. I will be very glad and indebted if you can help me with my issues. Thank you PS. I am attaching my Clover/IORegFiles/KextOutput ioreg.zip