fgalan

Done Thanks Man, it works like a charm. e1000=0 was not in the boot arguments. Fran

Hello guys, I was updating without major issues from 12.1 to 12.2 but with 12.3.1 seems something wrong. After a few seconds the mouse and the keyboard freezes and cannot do nothing except hard reset. Did you experienced something like this?

Finally I had success installed Monterey and updated to 12.1 right now.... from a fresh install as suggested by Maldon I had used the Clover300-400 EFI file and it boots. Copied EFI folder to the EFI partition and run runmeapp. I attached the dump. USB seems not to work, and the Graphics card Radeon RX580 seems not to work too. Please could you have a look in to my dump? please enable the virtualization in the ACPI to use VMWare as in Catalina. Thanks Maldon, Already sent a coffee to you... Send me Mac-Pro-de-Fran.zip

Hello Guys, I still dealing with the upgrade to Big Sur/Monterrey. I tried a fresh install from Big Sur and Monterrey, but it always give the same error. After the first stage booting the installer, I cannot reach the macos installer… the installer crash after loading something called AppleHIdDriver ( it stucks there for a couple of minutes) and the computer then reboots with a Bios CPU overtemperature alarm. I tried the raw Olarila image from Monterrey, same result. This image with my current EFI, same result. Update my currente EFI from Catalina with OP 7.5 and then upgrade from Catalina to Monterrey, same result… What I am missing? Thanks in advance Fran

Hello Maldon, VMX disabled in UEFI... sorry maybe I did not saved it properly. Now it works like a charm. About the second question in my previous post? what about to upgrade to Big Sur? I tried and it with the current config and it was unable to boot anymore... I reinstalled Catalina back. Thanks

Hello Maldon, This is an EFI folder to fix the virtualization? I swapped the old one an VMFusion still not working. Se snapshot about error. Captura de pantalla 2021-10-14 a las 9.07.34.zip

EFI folder attached. DisableIOMapper quirk disabled.... I hope. Still not working. Thanks Maldon EFI.zip

Hello Successfully installed Catalina on this MoBo with the Maldon Help, but still two questions. How can I enable VT-x and Vt-d virtualization? I would to run some virtual machines with VMWare Fusion and also run docker if it is possible. I enabled Vt-d in the BIOS but no changes in the results. May something to change in the ACPI. Second question is about to update to Big Sur, I am unable to boot in to the installer or upgrade from Catalina itself. In the last case the installer runs success but unable to boot anymore. Somebody installed Big Sur as far I had seen, could you share your EFI? Regards Fran

Attached a RunMe Dump Thanks Send me Frans-Mac-Pro.zip

Hello Maldon, Sorry but with your EFI folder the ethernet should work isn’t it? I installed Catalina with your EFI folder with no problems, but the built in ethernet still not detected... what patch you mean? Sorry for deal you, I am pretty new with hackintosh. Let me know what I need to do. Ethernet seems to be the only thing does not work. Regards Fran

Graphics works ok, in fact the card is recognized in the system properties. What about the ethernet is not recognized? Due to graphics?

Ola Maldon, I was using your EFI files, and the system boots in to installer for Catalina, no lucky for Big Sur. I installed Catalina but, built in ethernet does not work. Setup: Asus ProArt 10G i9 10900K unlocked con CFG unlock needed, as far I know XFX RX 580 8GB SAMSUNG 840 EVO 120GB SSD The system installed properly, and in the final installation stage if I check “connect to internet” the installer crashes. I finally check “No connect to internet” and the installer finished properly, but the ethernet as expected dors not work. I used the CLOVER EFI, could be different with OC? Regards Fran