Adam Peter

It goes to sleep now after 1 min , starts up when I press the power button on the case, but the monitors never turn on afterwards, using RX570 with 2 monitors

Maldon is there a guide to help try to find out why computer wont go to sleep?

I installed Ventura and wifi works but Bluetooth wont connect to anything . Will you be so kind to look at the usbports.kext maybe you can spot something All the usb ports work as USB2 only I put in 2 pics to show the mapping have no idea what's wrong Thanks Z790 USB.zip

It works after 2 nvram resets, Maldon do you know if Intel AX211 works on Sonoma? I mapped the usb not sure if it's ok but wifi doesn't work at all, bluetooth works but can't connect to anything.

Could not boot with Olaria.efi but I managed to do it with an Efi I found on the net. Geekbench 6 scores are low 2600/15000k , the wifi doesn't work bluetooth works but can't connect to anything,

I just built a new hack Z790+I7 would be grateful for a patched DSDT and a correct config for my mobo and cpu,had to remove ioreg was too large. Thanks and best regards SEND-ME-IMACPRO.zip

By the way does using SSDT'S make a difference instead of DSDT?

Thanks for the reply Maldon sysctl machdep.xcpm.mode gives me 0 .I uploded my EFI folder to https://filetransfer.io/data-package/wLO1OX1r#link. Thanks for the help and support!!!! Screenshot 2023-04-19 at 20.22.20.zip

I'm running an Asus x99 with E5 2696v3 xeon WITH UNLOCKED msr2 and turbo boost , can t get the cpu power management to work. Created with ssdt prgen an SSDT and made CPUFriendDataProvider.kext plus Cpufriend kext my system is on idle 52 degrees celsius which didn'T happened before with xcpm kernel patches. I added the SSDT along with my DSDT to my OC folder made snapshot with Propertree saved it ,with or without the SSDT same results CPU power management doesn't work I will upload my config dsdt that ssdt that was created and the CPUFriendDataProvider kext maybe someone can spot the problem. Any help is highly appreciated thanks!!!! X99.zip

Thanks for the reply Maldon , I can't boot off the EFI u sent me even after cleared NVRAM. I forgot to tell you if I deselect all kernel patches the cpu gets very hot 65-70 degrees on idle (with patches 42) There are no new xcpm patches Nmano closed the thread " The contents of these post are outdated, all the XCPM patches for X99 and similar chipsets can be enabled within Kernel → Quirks section" If I enable AppleCpuPmCfgLock, AppleXcpmExtraMsrs, AppleXcpmForceBoost same result high CPU Temps if disable same. Bios is set to C1 C3 enabled and C6 non retention state. Thanks again

I disabled all of them still the same , the guys from tony said it s a problem that I use DSDT and not SSDT. I have no clue. Thanks for the reply Maldon!!!! config.plist.zip

I'm running 12.5 on Asus x99 with E5 2696 v3 Xeon.The bios is unlocked for max turbo ( for xeon) and also MSR 0xe2 unlock.Lately the single core wont go higher than 2.8 when it should be 3.8 Ghz.The all core turbo is even better than it was , the problem is with the single core pref.I will upload the EFI maybe someone can spot, anything wrong.Thanks EFI.zip

Thank you for the DSDT Maldon ,maybe dumb question but do I need other SSDT'S to add like SSDT-RTC0-Range, SSDT-EC SSDT PLUG ? Thanks again!!!!

I have an ASUS X99 A2 mobo with unlocked bios and turbo unlocked for xeon CPU . Now running Catalina with Clover ,but was able to install Big sur with open core . The problem is BIG SUR sometimes it boots up sometimes is not and freezes and unfortunately my stable Catalina started now to freeze . I will attach DSDT extracted and also Opencore folder maybe someone can spot the problem I'm not a patch wizard by any means just a musician. Any help is highly appreciated Thanks and best regards DSDT.zip

Thanks for the help Maldon but it doesn't work I formatted the ssd named it Big sure after installation 12 minutes remaining it restarts and it comes back. It sees all my other SSD s only the Big SUR one doesn't. I have another option Mac os installation or something like that(not from the USB) when I try to boot that partition it starts white bar is charging for a bit after that it restarts the PC with error